Type: Driver
File Name:
File Size: 30.2 MB
29 (4.31)
Downloads: 15
Supported systems: Windows 2008, Windows XP, Windows Vista, Windows 7/8/10
Price: Free* (*Free Registration Required)

Download Now

I know that these concepts seem fairly straight forward now, but to a beginner this is some very useful ethernet flexnic lom to get started with HP Virtual Connect. I hope to have some more blog posts in the future about configuring networking with Virtual Connect. Glad I found this blog and great post.


Very much appreciated any help. Cheers, Yassen. Thanks for your help. February 8th, at Name required. E-Mail will not be published required. Subscribe to comments feed. My Tweets. Ethernet flexnic lom for session ! Thank you.

Barry February 18, at am. Leave a Reply Cancel reply Enter your comment here I never ethernet flexnic lom one on the web. The Onboard Administrator port mapping list is designed to show which interconnect port is connected to each server mezz port. Please rate the information on this page to help us improve our content. The HP interconnect modules have downlink and uplink ports.

The uplink ports ethernet flexnic lom pretty obvious, as they have a port on them that can be connected to a switch or ethernet flexnic lom device. The downlink ports are less obvious. Subscribe to comments feed. Now with many ProLiant Gen8 servers, our customers can now choose the type of network adapter they want. These are pretty straight forward and should be known to all HP c-Class Administrators.

It does not adjust, or directly impact the value of the Requested Bandwidth you can set at the other resources; Networks, Network Sets and Server Profile Connections. Except you are not using 2 x 10Gbps. Your adapter has two physical ports if we take the flb adapter as ethernet flexnic lom exampleeach with a max connection of 10Gbps.

HPE Support document - HPE Support Center

Please note that the connections that are drawn below are hardwired connections on the Backplane of ethernet flexnic lom HP c Enclosure. The other locations indicated in blue can only be FlexNics. Be sure to look at the release notes to get all the details. Our engineering team both hardware and firmware worked overnights to make it happen in VC 4. I set the module in interconnect bay 5.

HP Virtual Connect Basics

The module received ip the address on dhcp. But I don't understand ethernet flexnic lom it to control, the web isn't present the interface. These have 1 GB downlinks to the blades. I think each blade would be presented with 4 x Gigabit Nics, the additional 1Gb ports on the mezzanine card can only be used with additional switches in the Interconnect Bays. I think vmnic0 and vmnic1 would route through the x in Interconnect Bays 1 and 2 and vmnic2 and vmnic3 would route through the x in Interconnect Bays 3 and 4.

Would it form a single logical switch? This may dictate how many uplinks you require. As for redundancy you would need to work out whether you would build this into your Cisco networking topology and have failover happen at the Cisco level or take it down ethernet flexnic lom your ESX level and get the ESX hosts to handle failover between the vmnics.

HPE Virtual Connect Flex-10 Ethernet Module - Overview

I am a bit unsure on the Physical connections HP say one type of cable, Cisco have a different one. Share this: Twitter Facebook.

minolta dialta di2011HP Virtual Connect 4.01 Update: Min/Max Bandwidth Optimisation
mga g550 agpRecent Posts
ess es1969 gameport joystickHPE Support Center
gigabyte ga-k8vm800m displayWhat is a Virtual Connect Flex10?

You would have to go into VC and manually reconfigure the FlexNic bandwidth.This new Flexible LOM provides our customer the ability to customize 10 Gb port 1: Up to 3x Ethernet (FlexNics) ethernet flexnic lom 1x Fibre Channel (over. One of the things I spent a few days looking for was a LOM port map for a full height blade Ethernet FlexNIC (NIC 3) LOMb, vmnic

Other Drivers